Physics Wallah

Op-Amp Positive Feedback and Schmitt Trigger Analysis for GATE 2027 ECE, EE and IN

Op-amp positive feedback drives the output towards positive or negative saturation. Schmitt triggers use two switching thresholds to create hysteresis. Understand threshold calculations for inverting and non-inverting configurations, Zener-clamped outputs and MOSFET operating-region checks for GATE 2027.
authorImageAnshika Agarwal18 Nov, 2026
Op-Amp Positive Feedback and Schmitt Trigger Analysis for GATE 2027 ECE, EE and IN

Operational amplifiers (op-amps) with positive feedback are important in analogue electronics, particularly in switching circuits such as Schmitt triggers. Unlike negative feedback, positive feedback drives the op-amp towards one of its saturation states. Understanding this behaviour helps solve questions on threshold detection, hysteresis, waveform shaping and switching conditions.

For GATE 2027 ECE, EE and IN aspirants, these concepts require an understanding of terminal voltages, feedback networks and operating conditions. GATE Wallah offers concept-focused courses, topic-wise and subject-wise tests, and full-length mock tests to support preparation across these streams.

Fundamental Concept of Op-Amp Positive Feedback

For an op-amp using positive feedback, the output saturates at one of the supply rails:

Vₒᵤₜ = +Vₛₛ or Vₒᵤₜ = −Vₛₛ

The output polarity depends on the comparison between the input terminal voltages:

  • If V₊ > V₋, then Vₒᵤₜ = +Vₛₛ.

  • If V₋ > V₊, then Vₒᵤₜ = −Vₛₛ.

The three essential points are:

  • Positive feedback means that the output is connected to the non-inverting input.

  • The output is restricted to +Vₛₛ or −Vₛₛ.

  • The output polarity depends on whether V₊ is greater than or less than V₋.

In positive feedback, the output does not remain in a linear amplification region. It switches between the two saturation levels.

Types Of Schmitt Triggers

Configuration

Input Location

Feedback Location

Inverting Schmitt Trigger

Inverting terminal

Non-inverting terminal

Non-Inverting Schmitt Trigger

Non-inverting terminal

Non-inverting terminal

Memory Tip: Do not memorize separate formulas for each circuit. Confirm positive feedback, assume one output saturation level, calculate V₊ and V₋, apply the switching condition, and repeat for the opposite output level. The procedure is more important than memorising formulas.

Inverting Schmitt Trigger

In an inverting Schmitt trigger, the input is applied to the inverting terminal, and positive feedback is applied to the non-inverting terminal.

The terminal voltages are:

V₋ = Vᵢ

V₊ = Vₒ × R₂ / (R₁ + R₂)

Threshold Analysis

Assume first that:

Vₒ = +Vₛₛ

Then:

V₊ = Vₛₛ × R₂ / (R₁ + R₂)

The output changes from +Vₛₛ to −Vₛₛ when V₋ becomes greater than V₊. Therefore:

Vᵢ > Vₛₛ × R₂ / (R₁ + R₂)

The upper threshold is:

Vᵤₜ = +Vₛₛ × R₂ / (R₁ + R₂)

Now assume:

Vₒ = −Vₛₛ

Then:

V₊ = −Vₛₛ × R₂ / (R₁ + R₂)

For the output to change from −Vₛₛ to +Vₛₛ, V₊ must become greater than V₋. Hence:

Vᵢ < −Vₛₛ × R₂ / (R₁ + R₂)

The lower threshold is:

Vₗₜ = −Vₛₛ × R₂ / (R₁ + R₂)

Hysteresis Voltage

The hysteresis voltage is the difference between the upper and lower thresholds:

Vₕ = Vᵤₜ − Vₗₜ

For the symmetric circuit:

Vₕ = 2Vₛₛ × R₂ / (R₁ + R₂)

The switching behavior is:

  • When the input increases beyond Vᵤₜ, the output changes from +Vₛₛ to −Vₛₛ.

  • When the input decreases below Vₗₜ, the output changes from −Vₛₛ to +Vₛₛ.

The two different switching levels prevent unwanted output changes due to small input noise.

Planning your GATE 2027 preparation in Computer Science or Data Science and Artificial Intelligence? Explore GATE Wallah's CSE and DA courses. 

Non-Inverting Schmitt Trigger

In a non-inverting Schmitt trigger, the input and positive feedback are connected to the non-inverting terminal. For the circuit discussed:

V₋ = 0

Applying KCL at the non-inverting terminal gives:

V₊ = (R₁Vᵢ + R₂Vₒ) / (R₁ + R₂)

Threshold Analysis

Assume:

Vₒ = +Vₛₛ

Then:

V₊ = (R₁Vᵢ + R₂Vₛₛ) / (R₁ + R₂)

For the output to switch from +Vₛₛ to −Vₛₛ, V₊ must become less than V₋, which is zero. Therefore:

Vᵢ < −R₂Vₛₛ / R₁

The lower threshold is:

Vₗₜ = −R₂Vₛₛ / R₁

Now assume:

Vₒ = −Vₛₛ

Then:

V₊ = (R₁Vᵢ − R₂Vₛₛ) / (R₁ + R₂)

For the output to switch from −Vₛₛ to +Vₛₛ, V₊ must become greater than zero:

Vᵢ > R₂Vₛₛ / R₁

The upper threshold is:

Vᵤₜ = +R₂Vₛₛ / R₁

Therefore, the hysteresis voltage is:

Vₕ = Vᵤₜ − Vₗₜ

For the symmetric case:

Vₕ = 2R₂Vₛₛ / R₁

Memory Tip: For both Schmitt trigger configurations, first find the output saturation level, determine the feedback voltage, compare V₊ and V₋, and repeat the process for the opposite saturation level.

Schmitt Trigger With A Sinusoidal Input

Consider a Schmitt trigger with supply rails of +5 V and −5 V and a sinusoidal input having an amplitude of 1 V. The input varies only from −1 V to +1 V.

If the switching thresholds are −4 V and +6 V, the input never reaches either threshold. Therefore:

  • The output does not switch.

  • The output remains at its initial saturation level.

  • A Schmitt trigger changes state only when the input crosses the relevant threshold.

This result is useful in waveform and threshold-crossing questions.

Zener-Clamped Schmitt Trigger

A Zener diode can limit the externally observed output without changing the op-amp’s internal saturation voltage.

For example:

Quantity

Positive State

Negative State

Op-Amp Internal Output

+15 V

−15 V

Circuit Output After Zener Clamping

+7 V

−7 V

The switching condition is determined using the op-amp saturation levels, while the circuit output is limited to the Zener voltage.

For the given circuit, the thresholds are approximately:

V_T1 = 2.23 V

V_T2 = 1.5714 V

The output changes between +7 V and −7 V.

Memory Tip: When Zener diodes are present, use the op-amp saturation values while finding the switching condition. Use the clamped values only for the actual external circuit output.

Planning your GATE CSE and DA 2027 preparation in the final six months? Follow this last six-month roadmap for GATE CSE and DA 2027 for a month-wise study strategy.

MOSFET Operating-Region Checks

MOSFET questions often require identifying the operating region before calculating current or voltage.

For two identical NMOS devices connected in series:

  • The devices carry the same drain current.

  • If both are in saturation, their V_GS values are equal.

  • A device with a larger V_GS generally tends toward the ohmic region.

  • The device with a smaller V_GS generally remains in saturation.

For a device with its drain and gate shorted, the MOSFET operates in saturation. In the discussed series example, both MOSFETs are in saturation, and equal V_GS values divide the total gate-related voltage equally.

The saturation current relation is:

I_D = K_N (V_GS − V_T)²

For two identical devices with V_GS = 2 V and V_T = 1 V, the lecture gives:

I_D = 2 mA

Always verify the assumed operating region after calculating the node voltage.

Op-amp positive feedback and Schmitt triggers are important analogue electronics topics for GATE ECE, EE and IN. Understanding the difference between inverting and non-inverting configurations, deriving upper and lower thresholds, calculating hysteresis voltage, and analysing Zener-clamped outputs can help you approach circuit-based questions systematically. 

For comprehensive preparation, GATE Wallah offers 10+ Electronics, Electrical and Instrumentation courses, along with concept-focused learning and topic-wise, subject-wise, multiple-subject and full-length tests. You should use these resources to strengthen your understanding of analogue electronics and related subjects, practise examination-style questions and track your preparation through performance assessments.

FAQs

1. What is positive feedback in an op-amp?

Positive feedback occurs when a portion of the output is fed back to the non-inverting input. It reinforces the output response and generally drives the op-amp towards positive or negative saturation.

2. What is a Schmitt trigger?

A Schmitt trigger is a comparator circuit that uses positive feedback to establish two switching thresholds. The difference between these thresholds creates hysteresis.

3. What is the difference between inverting and non-inverting Schmitt triggers?

In an inverting Schmitt trigger, the input is applied to the inverting terminal and positive feedback is applied to the non-inverting terminal. In a non-inverting Schmitt trigger, the input and positive feedback are connected to the non-inverting terminal.

4. Why are Zener diodes used in Schmitt trigger circuits?

Zener diodes can clamp the externally observed output voltage to specified levels. The internal op-amp saturation and the clamped output must be considered separately during circuit analysis.
Join 15 Million students on the app today!
Point IconLive & recorded classes available at ease
Point IconDashboard for progress tracking
Point IconMillions of practice questions at your fingertips
Download ButtonDownload Button
Banner Image
Banner Image
Free Learning Resources
Know about Physics Wallah
Physics Wallah is an Indian edtech platform that provides accessible & comprehensive learning experiences to students from Class 6th to postgraduate level. We also provide extensive NCERT solutions, sample paper, NEET, JEE Mains, BITSAT previous year papers & more such resources to students. Physics Wallah also caters to over 3.5 million registered students and over 78 lakh+ Youtube subscribers with 4.8 rating on its app.
We Stand Out because
We provide students with intensive courses with India’s qualified & experienced faculties & mentors. PW strives to make the learning experience comprehensive and accessible for students of all sections of society. We believe in empowering every single student who couldn't dream of a good career in engineering and medical field earlier.
Our Key Focus Areas
Physics Wallah's main focus is to make the learning experience as economical as possible for all students. With our affordable courses like Lakshya, Udaan and Arjuna and many others, we have been able to provide a platform for lakhs of aspirants. From providing Chemistry, Maths, Physics formula to giving e-books of eminent authors like RD Sharma, RS Aggarwal and Lakhmir Singh, PW focuses on every single student's need for preparation.
What Makes Us Different
Physics Wallah strives to develop a comprehensive pedagogical structure for students, where they get a state-of-the-art learning experience with study material and resources. Apart from catering students preparing for JEE Mains and NEET, PW also provides study material for each state board like Uttar Pradesh, Bihar, and others

Copyright © 2026 Physicswallah Limited All rights reserved.