
Mechanical Properties of Fluids is an important chapter in the NEET Physics syllabus. It explains how liquids and gases behave under pressure, gravity and motion. You will study concepts such as pressure, buoyancy, fluid flow, viscosity and surface tension, along with the principles used to solve numerical questions.
For NEET, focus on understanding the application of formulas rather than memorising them alone. Questions from this chapter often involve pressure differences, floating bodies, Bernoulli’s equation, terminal velocity and capillary rise. A clear understanding of these concepts will help you solve numerical problems with better accuracy.
Mechanical Properties of Fluids in NEET are the physical properties that explain how liquids and gases behave under pressure, gravity, motion and surface forces.
Pressure is the force acting normally on a surface per unit area.
Pressure is given by:
P = F/A
For a small area:
dF = P dA
Therefore, the total force is:
F = integral of P dA
If pressure is uniform over the surface:
F = PA
The relation F = PA is valid only for uniform pressure. Pressure force acts perpendicular to the surface and towards the body.
In a liquid, pressure increases with depth:
P = P0 + rho gh
The gauge pressure is:
P(gauge) = rho gh
In the same continuous liquid, pressure is equal at the same horizontal level.
For pressure calculations:
Moving downward: add rho gh.
Moving upward: subtract rho gh.
Moving horizontally at the same level: pressure does not change.
On entering another liquid, use its density.
In an accelerating frame, pressure increases towards the pseudo force.
You can also practise questions using NEET previous year question papers.
For a liquid in a horizontally accelerating container:
tan theta = a/g
The pressure difference between two points separated horizontally by distance L is:
Delta P = rho aL
Pressure increases in the direction of the pseudo force.
For a rotating liquid, pressure increases away from the axis:
P2 - P1 = 1/2 rho omega^2 (R2^2 - R1^2)
The free surface of a rotating liquid is parabolic:
y = omega^2 x^2 / 2g
Volume conservation must be applied whenever the liquid redistributes.
Pascal’s law states that pressure applied to a confined fluid is transmitted equally and undiminished throughout the fluid.
For a hydraulic press:
F1/A1 = F2/A2
For circular pistons, area is proportional to the square of diameter:
A is proportional to d^2
Therefore, a small force on a small piston can produce a larger force on a large piston. When pistons are at different heights, include the hydrostatic term rho gh in the pressure balance.
Buoyant Force And Floating Bodies
The pressure at the lower surface of an immersed body is greater than the pressure at its upper surface. The resultant upward force is buoyancy:
FB = rho(liquid) V(displaced) g
For a floating body:
FB = mg
Therefore:
rho(liquid) V(displaced) = m
The density used for buoyant force is the liquid density, while the density used for weight is the body density.
If a floating body is placed in a lift or on another planet, the submerged fraction remains unchanged because the effective gravitational acceleration cancels from the equilibrium equation.
The equation of continuity follows conservation of mass. For steady flow
rho A1 v1 = rho A2 v2
For an incompressible liquid:
A1 v1 = A2 v2
The volume flow rate is:
dV/dt = Av
The mass flow rate is:
dm/dt = rho Av
Thus, a narrow section of a pipe has greater velocity, while a wider section has lower velocity.
For steady flow of an ideal fluid:
P + rho gh + 1/2 rho v^2 = constant
The terms represent pressure energy, gravitational energy, and kinetic energy per unit volume.
For a horizontal pipe:
P1 - P2 = 1/2 rho (v2^2 - v1^2)
Therefore, when fluid speed increases in a narrow section, pressure decreases. Continuity and Bernoulli’s equation are usually applied together in pipe and Venturi-meter problems.
For a Venturi meter, pressure difference may also be measured through a liquid column:
Delta P = rho g Delta h
For a small hole at depth h below the free surface, Torricelli’s law gives:
v = square root of (2gh)
The volume flow rate through the hole is:
dV/dt = A square root of (2gh)
where A is the area of the hole.
If the jet leaves horizontally from height h above the ground and the liquid surface is at height H, its range is:
R = 2 square root of [h(H - h)]
The range is maximum when the hole is halfway between the liquid surface and the ground.
The thrust produced by the outgoing liquid is:
F = v(dm/dt) = rho A v^2
Viscosity opposes relative motion between fluid layers. The viscous force is:
F = eta A (dv/dx)
The shear stress is:
F/A = eta (dv/dx)
For a small sphere moving through a viscous fluid, Stokes’ law is:
Fv = 6 pi eta r v
At terminal velocity, the net force is zero. For a sphere:
vt = 2 r^2 g (rho sphere - rho liquid) / 9 eta
Thus, terminal velocity is proportional to the square of radius and inversely proportional to viscosity.
The Reynolds number is:
Re = rho v D / eta
It helps identify laminar, transitional, and turbulent flow.
Surface tension is force per unit length:
Surface tension = Force / Length
Surface energy is:
E = sigma A
A liquid drop has one free surface, while a soap bubble has two.
For a liquid drop:
Excess pressure = 2 sigma / r
For a soap bubble:
Excess pressure = 4 sigma / r
The factor of 2 for a soap bubble must not be omitted, because it has two surfaces.
When drops merge or split, volume is conserved. If n identical drops of radius r merge:
R = n^(1/3) r
Since terminal velocity depends on r^2, the final terminal velocity becomes:
vt(final) = n^(2/3) vt(initial)
Practise numerical questions using NEET Physics chapter-wise PYQs to understand the application of continuity and Bernoulli's equations.
The capillary rise is:
h = 2 sigma cos theta / (r rho g)
where theta is the angle of contact and r is the capillary-tube radius.
Capillary height:
Increases with surface tension.
Decreases with tube radius.
Decreases with liquid density.
Decreases with effective gravitational acceleration.
Depends on cos theta, not directly on theta.
If the calculated rise exceeds the tube length, the liquid can rise only up to the top of the tube.
For further revision, refer to NEET study material and practise questions from different Physics chapters.