Physics Wallah

JEE Advanced Misconceptions in Collision Notes by Physics Wallah

Finding collision problems involving friction and impulse difficult to revise? Physics Wallah notes help you understand kinetic and static friction, normal impulse, slipping conditions, and rebound direction. Revise frictional impulse concepts and practise advanced collision problems for JEE Advanced Physics.
authorImageMehjabeen Hussain18 Nov, 2026
JEE Advanced

Collision problems involving friction are an important part of JEE Advanced Mechanics. Questions often involve blocks moving on rough surfaces, objects sticking together and bodies colliding with walls, where assuming friction acts throughout the collision or confusing maximum frictional impulse with actual frictional impulse can lead to incorrect answers.

For focused revision, Physics Wallah’s Collision notes for JEE Physics help you revisit essential concepts, impulse-momentum principles and frictional impulse calculations. Review the formulas below and practise applying them to collision problems to improve accuracy in JEE Advanced.

Momentum Transfer: Block and Vertically Dropped Mass

A 5 kg block moves horizontally at 2 m/s on a rough horizontal surface. A 1 kg object is dropped vertically onto it with a downward speed of 10 m/s. The object sticks to the block. The coefficient of friction between the block and the ground is 0.4.

Since the collision is momentary, the objects move together immediately after impact with a common horizontal velocity V.

The collision involves both horizontal and vertical momentum changes. The vertical impulse helps determine the normal impulse, which is then used to calculate the possible frictional impulse.

Calculating the Normal Impulse

Consider the block and the dropped object as a single system.

The contact force between the two objects is internal to the system. The weight of the objects is a non-impulsive force during the very short collision and can be neglected.

Initially, the dropped object has downward vertical momentum:

Initial vertical momentum = 1 × 10 = 10 kg m/s

After the collision, the combined system has zero vertical velocity.

Therefore, the change in vertical momentum is 10 kg m/s upward.

The ground provides an upward normal impulse:

Normal impulse = 10 N s

This normal impulse is used to determine the maximum possible frictional impulse during the collision.

The Common but Incomplete Method

A frequently used calculation is:

Frictional impulse = Coefficient of friction × Normal impulse

Frictional impulse = 0.4 × 10 = 4 N s

The initial horizontal momentum of the block is:

Initial horizontal momentum = 5 × 2 = 10 kg m/s

The total mass after the collision is:

Total mass = 5 + 1 = 6 kg

Applying the horizontal impulse-momentum equation:

-4 = 6V - 10

Therefore:

V = 1 m/s

The numerical answer is correct in this case. However, directly using the maximum frictional impulse without identifying the type and duration of friction does not provide complete physical reasoning.

A correct numerical result does not necessarily validate the method used to obtain it.

Identifying the Type of Friction

The ground is stationary, whereas the block initially moves horizontally at 2 m/s.

Therefore, relative motion exists between the block and the ground. Kinetic friction acts initially.

The two main types of friction are:

Kinetic Friction: It acts when two contacting surfaces slide relative to each other.

Static Friction: It acts when there is no relative slipping between the contacting surfaces and prevents relative motion from starting.

Static friction cannot act initially in this example because the block is already sliding relative to the ground.

The correct initial relation is:

Kinetic friction = Coefficient of kinetic friction × Normal reaction

Kinetic-Friction Impulse and Its Duration

The normal reaction may act throughout the collision interval, represented by Δt. However, kinetic friction acts only while relative slipping continues.

Let Δt₁ represent the duration for which kinetic friction acts.

The kinetic-friction impulse is:

Kinetic-friction impulse = μₖ × Normal impulse accumulated during Δt₁

Therefore:

Δt₁ ≤ Δt

If slipping continues throughout the collision, Δt₁ = Δt.

For the given coefficient of friction, the maximum possible frictional impulse is:

Maximum frictional impulse = 0.4 × 10

Maximum frictional impulse = 4 N s

Using this impulse:

-4 = 6V - 10

V = 1 m/s

Since the final horizontal velocity is positive, the combined system continues moving in the original direction.

Therefore, slipping continues throughout the collision, and the assumption of full-duration kinetic friction is self-consistent.

Physical Check of the Final Velocity

The final velocity must always be checked after calculating the frictional impulse.

A positive final velocity indicates that the system continues moving in the original direction.

A zero final velocity indicates that the relative slipping has stopped.

A negative final velocity obtained by assuming full-duration kinetic friction may indicate that the assumed frictional duration is incorrect.

The actual motion must determine the frictional impulse, not simply the maximum value allowed by the coefficient of friction.

Larger Friction Coefficient: Why a Negative Result Is Invalid

Now consider a larger coefficient of kinetic friction of 2.2.

The maximum possible frictional impulse is:

Maximum frictional impulse = μₖ × Normal impulse

= 2.2 × 10

Maximum frictional impulse = 22 N s

If kinetic friction is assumed to act throughout the entire collision, the horizontal impulse-momentum equation becomes:

-22 = 6V - 10

Therefore:

V = -2 m/s

This negative velocity is not the physically valid result under the assumed friction model.

The initial horizontal momentum is 10 kg m/s in the forward direction.

A backward frictional impulse of only 10 N s is sufficient to reduce the horizontal velocity to zero.

Once the block stops sliding relative to the ground, kinetic friction cannot continue acting in the same direction to reverse its motion.

Therefore:

  • Slipping stops before the collision ends.

  • Kinetic friction acts for a shorter duration.

  • The actual frictional impulse is 10 N s.

  • The final horizontal velocity is zero.

The impulse required to stop the slipping is:

Required frictional impulse = Initial horizontal momentum

Required frictional impulse = 10 N s

The normal impulse accumulated during the slipping period can be calculated using:

Actual frictional impulse = μₖ × Normal impulse during slipping

10 = 2.2 × Normal impulse during slipping

Therefore:

Normal impulse during slipping = 10/2.2 N s

The kinetic-friction impulse is limited to the amount required to stop the slipping.

After slipping stops, static friction can maintain zero relative velocity if required. In this example, no further horizontal frictional impulse is necessary.

Memory Tip: Friction does not automatically apply its maximum possible impulse. It acts according to the relative motion between the surfaces. A negative final velocity can indicate that the assumption of full-duration kinetic friction is invalid.

Angle-Changing Bounce from a Vertical Wall

Consider a cube sliding without friction on a horizontal floor and colliding with a vertical wall. One face of the cube is parallel to the wall.

The coefficient of friction between the cube and the wall is 2, and the coefficient of restitution is one-half.

The initial velocity makes an angle of 37° with the wall.

Let the initial speed be v.

Resolving the velocity into components:

Component parallel to the wall:

vₜ = v cos 37°

vₜ = 4v/5

Component perpendicular to the wall:

vₙ = v sin 37°

vₙ = 3v/5

The collision changes the normal and tangential components differently.

Normal Component After Collision

For a collision with a fixed wall, the coefficient of restitution determines the normal component of velocity after impact.

Coefficient of restitution = Final normal speed / Initial normal speed

Therefore:

Final normal speed = Coefficient of restitution × Initial normal speed

vₙ' = 1/2 × 3v/5

vₙ' = 3v/10

The normal velocity reverses its direction after the collision.

If the mass of the cube is m, the normal impulse is calculated using the change in normal momentum.

Normal impulse = m(3v/5 + 3v/10)

Therefore:

Normal impulse = 9mv/10

Struggling with frictional impulse and advanced collision problems in JEE preparation? Strengthen your concepts with PW’s JEE batches

Frictional Impulse and Rebound Direction

The maximum frictional impulse available at the wall is:

Maximum frictional impulse = Coefficient of friction × Normal impulse

= 2 × 9mv/10

Maximum frictional impulse = 9mv/5

The initial tangential momentum is:

Tangential momentum = m × 4v/5

Tangential momentum = 4mv/5

To eliminate the tangential velocity completely, friction must provide a tangential impulse equal to the initial tangential momentum.

Required frictional impulse = 4mv/5

The maximum available frictional impulse is:

Maximum frictional impulse = 9mv/5

Since:

9mv/5 > 4mv/5

The available frictional impulse is sufficient to eliminate the entire tangential component of velocity.

Therefore, the cube loses its tangential velocity and rebounds only in the normal direction.

The final velocity is perpendicular to the wall.

Angle of rebound with the wall = 90°

The important point is that the actual frictional impulse required to stop tangential slipping is 4mv/5, not the maximum available impulse of 9mv/5.

General Method for Solving Collision Problems with Friction

Follow these steps to solve advanced collision problems involving friction:

  1. Identify the system and calculate the initial momentum.

  2. Calculate the normal impulse using the impulse-momentum principle.

  3. Identify whether relative slipping exists at the beginning of the collision.

  4. Apply kinetic friction when relative slipping is present.

  5. Calculate the maximum available frictional impulse.

  6. Compare it with the impulse required to eliminate the relative tangential velocity.

  7. If slipping continues, calculate the frictional impulse over the slipping duration.

  8. If slipping stops early, limit the kinetic-friction impulse to the amount required to stop slipping.

  9. Check whether static friction is needed to maintain zero relative velocity.

  10. Verify that the calculated final motion is physically consistent.

These steps help avoid incorrect assumptions about frictional impulse and make collision problems easier to approach systematically.

Collision concepts are essential for solving advanced mechanics problems involving impulse, momentum and friction in JEE Physics. Revise kinetic and static friction, normal impulse, frictional impulse and slipping conditions carefully, and practise applying them to block and wall collision problems. PW’s Collision notes for JEE Advanced help you strengthen these fundamentals before moving to more complex mechanics topics.

You may also like : 

Resource Name

Link

JEE Syllabus

View

JEE Advanced Formulas

View

JEE Advanced Sample Paper

View

JEE Advanced PYQs

View

 

FAQs

Which type of friction acts initially when two surfaces are sliding?

Kinetic friction acts when relative motion exists between the contacting surfaces.

Can normal reaction and friction act for different durations during a collision?

Yes. The normal contact force may act throughout the collision, whereas kinetic friction acts only while relative slipping continues.

What does a negative final velocity usually indicate in a frictional collision problem?

It may indicate that kinetic friction has incorrectly been assumed to act throughout the entire collision. The actual slipping may stop earlier, limiting the frictional impulse.
Join 15 Million students on the app today!
Point IconLive & recorded classes available at ease
Point IconDashboard for progress tracking
Point IconLakhs of practice questions
Download ButtonDownload Button
Banner Image
Banner Image
Free Learning Resources
Know about Physics Wallah
Physics Wallah is an Indian edtech platform that provides accessible & comprehensive learning experiences to students from Class 6th to postgraduate level. We also provide extensive NCERT solutions, sample paper, NEET, JEE Mains, BITSAT previous year papers & more such resources to students. Physics Wallah also caters to over 3.5 million registered students and over 78 lakh+ Youtube subscribers with 4.8 rating on its app.
We Stand Out because
We provide students with intensive courses with India’s qualified & experienced faculties & mentors. PW strives to make the learning experience comprehensive and accessible for students of all sections of society. We believe in empowering every single student who couldn't dream of a good career in engineering and medical field earlier.
Our Key Focus Areas
Physics Wallah's main focus is to make the learning experience as economical as possible for all students. With our affordable courses like Lakshya, Udaan and Arjuna and many others, we have been able to provide a platform for lakhs of aspirants. From providing Chemistry, Maths, Physics formula to giving e-books of eminent authors like RD Sharma, RS Aggarwal and Lakhmir Singh, PW focuses on every single student's need for preparation.
What Makes Us Different
Physics Wallah strives to develop a comprehensive pedagogical structure for students, where they get a state-of-the-art learning experience with study material and resources. Apart from catering students preparing for JEE Mains and NEET, PW also provides study material for each state board like Uttar Pradesh, Bihar, and others

Copyright © 2026 Physicswallah Limited All rights reserved.