
Electromagnetic Waves is where electricity and magnetism come together. JEE questions test whether you can pick the right surface, field or relation, such as which current passes through an Amperian surface or how E₀ and B₀ are linked. A small slip, like reversing the spectrum order or the direction of propagation, changes the whole answer.
PW's Electromagnetic Waves notes start with the problem Maxwell set out to solve. They then cover displacement current, Maxwell's equations, wave properties, energy transport and the spectrum. Keep the Electromagnetic Waves JEE formula sheet beside you while revising.
When a capacitor is connected to a battery through a resistance, it charges gradually as an RC circuit. If you want to revisit the charging relations first, go through the JEE Capacitance Notes. The charge at time t is:
Q = Q₀ (1 − e^(−t/RC))
Here Q₀ = CV is the final charge on the capacitor.
Current flows through the wires, and the plates acquire equal and opposite charges. However, no ordinary conduction current flows through the insulating gap between the plates. Current appears in the wires but seems to stop between the plates, even though a complete circuit should have continuous current.
Maxwell resolved this using symmetry:
A time-varying magnetic field produces an electric field.
A time-varying electric field produces a magnetic field.
A compass placed between the plates of a charging capacitor also shows a deflection. This proves that a magnetic field exists in the gap even without conduction current.
The original Ampere’s law is:
∮B·dl = μ₀ I(c)
For a loop around the connecting wire, the law correctly predicts a magnetic field because conduction current is enclosed.
For a surface passing between the capacitor plates:
Conduction current is zero.
The original law predicts zero magnetic field.
Experiment shows that a magnetic field is present.
The original Ampere’s law is therefore incomplete for a charging capacitor.
Maxwell introduced displacement current to keep the current continuous and to explain the magnetic field between the plates. It is associated with a changing electric field, or changing electric flux, and not with electrons physically moving across the gap.
Memory tip: Displacement current is a supplementary term. It is added so that current stays continuous and Ampere’s law agrees with observation.
Conduction current, denoted I(c):
Flows through conducting wires.
Is caused by the motion of electrons.
Is the ordinary current.
Displacement current, denoted I(d):
Exists in the space between the capacitor plates.
Is caused by a time-varying electric field.
Is a current-like quantity linked with changing electric flux.
For a surface that covers the complete plate area, I(d) = I(c) in magnitude.
For a parallel-plate capacitor:
E = Q / (ε₀ A)
The electric flux through the complete plate area is:
Φ(E) = EA = Q / ε₀
As the capacitor charges, Q changes with time, so the electric flux also changes. The displacement current is:
I(d) = ε₀ (dΦ(E)/dt)
Substituting Φ(E) = Q / ε₀ gives I(d) = dQ/dt. Since the conduction current is also dQ/dt, I(d) = I(c).
The most useful forms are:
I(d) = ε₀ (dΦ(E)/dt)
I(d) = dQ/dt
I(d) = C (dV/dt), which applies to a capacitor of constant capacitance C
For a smaller surface of area a inside plates of area A:
I(d) = I(c) (a / A)
The total displacement current equals the conduction current only when the complete plate area is considered.
A capacitor has a capacitance of 2.5 μF and a displacement current of 25 mA. Find the rate of change of potential difference.
I(d) = C (dV/dt)
dV/dt = (25 × 10⁻³) / (2.5 × 10⁻⁶)
dV/dt = 10⁴ V/s
Maxwell modified Ampere’s law by including both currents:
∮B·dl = μ₀ (I(c) + I(d))
or
∮B·dl = μ₀ [I(c) + ε₀ (dΦ(E)/dt)]
For a surface around the wire, conduction current is present. For a surface between the plates, conduction current is zero but displacement current is present. Both surfaces now predict the same magnetic field.
Consider circular plates of radius R carrying a changing current I.
For an Amperian loop of radius r inside the plate region (r < R), only part of the displacement current is enclosed:
I(d) = I (r² / R²)
Using the modified Ampere’s law:
B = μ₀ I r / (2π R²)
Inside the plate region, B is proportional to r.
For a loop outside the plate radius (r > R), the complete displacement current is enclosed:
B = μ₀ I / (2π r)
Outside the plate region, B is proportional to 1/r. The field is maximum at the boundary, r = R:
B(max) = μ₀ I / (2π R)
Memory tip: Inside the plates, B increases with r. Outside, it falls as 1/r. The maximum sits at the edge.
Maxwell’s equations bring together everything the chapter has built so far:
Gauss’s law for electricity: electric flux depends on the enclosed charge.
Gauss’s law for magnetism: the net magnetic flux through a closed surface is zero because magnetic field lines form closed loops.
Faraday’s law: a changing magnetic flux produces an electric field. Revise it with the Electromagnetic Induction JEE notes.
Ampere-Maxwell law: conduction current and changing electric flux produce a magnetic field.
Together, these equations show that changing electric and magnetic fields generate each other.
Electromagnetic waves are produced by accelerating charges. An oscillating charge creates changing electric and magnetic fields that keep generating each other and travel through space.
Important properties:
The electric and magnetic fields are mutually perpendicular.
Both fields are perpendicular to the direction of propagation.
The two fields oscillate in phase.
The waves can travel through vacuum.
The direction of propagation is given by E × B.
They carry energy and momentum.
They are not deflected by external electric or magnetic fields because they carry no net charge.
A sinusoidal electric field can be written as:
E = E₀ sin(ωt − kx + φ)
where E₀ is the amplitude, ω is the angular frequency, k is the wave number and φ is the phase constant.
Important relations:
ω = 2πf
k = 2π / λ
v = ω / k = λf
c = 1 / √(μ₀ε₀)
E₀ / B₀ = c
In a medium:
v = 1 / √(με)
Refractive index: n = c / v
Energy density of the electric field: u(E) = ½ ε₀E²
Energy density of the magnetic field: u(B) = B² / (2μ₀)
For an electromagnetic wave, u(E) = u(B), so the energy is shared equally between the two fields. The average energy density is:
u(avg) = ½ ε₀E₀²
Intensity is the energy transmitted per unit area per unit time:
I = u(avg) × c
I = ½ ε₀E₀² c
The Poynting vector represents the flow of electromagnetic energy, and its direction is the direction of wave propagation. Electromagnetic waves also carry momentum, so they exert radiation pressure when they strike a surface.
Want more practice on E₀ and B₀ relations and intensity numericals? Attempt PW’s Electromagnetic Waves JEE PYQs with solutions.
Electromagnetic Spectrum
In order of increasing wavelength, the spectrum runs:
Gamma Rays → X-Rays → Ultraviolet → Visible Light → Infrared → Microwaves → Radio Waves
As the wavelength increases, frequency and energy decrease. Photon energy is:
E = hν = hc / λ
Memory tip: Moving from gamma rays towards radio waves, wavelength increases while frequency and photon energy fall.
Radio waves: used for communication and produced by oscillating electrons in antennas.
Microwaves: used in radar, speed guns, aircraft navigation and microwave ovens, and produced using a klystron valve.
Infrared waves: used for heat radiation, infrared lamps and physiotherapy.
Ultraviolet rays: used in LASIK surgery, and emitted by the Sun and very hot bodies.
X-rays: used in medical imaging and cancer treatment, and characteristic X-rays involve inner-shell electrons.
Gamma rays: associated with nuclear reactions and radioactive decay.
Infrared radiation is absorbed by carbon dioxide, water and ammonia. This absorption heats the surroundings and is linked with the greenhouse effect. The ozone layer helps protect living organisms from harmful ultraviolet radiation.
Want to check how well the spectrum order and uses have stayed with you? Attempt PW’s Electromagnetic Waves MCQs for JEE Main and Advanced.
Electromagnetic Waves becomes easier once you link each idea to the situation it explains: displacement current for the gap between the plates, E₀ / B₀ = c for the relation between the fields, and the spectrum order for questions on uses and energy. Revise the field around a charging circular capacitor, the energy and intensity relations, and the production and uses of each region of the spectrum. PW’s Electromagnetic Waves notes can support your JEE Main and Advanced preparation with a clear, concept-focused revision of the chapter.
Find displacement current and Maxwell’s equations easier to follow when a teacher explains them step by step? Learn with PW’s JEE online batches.
|
Resource Name |
Link |
|
JEE Syllabus |
|
|
JEE PYQs |
|
|
JEE Sample Paper |
|
|
JEE Main Formulas |
|
|
JEE Advanced Formulas |
|
|
JEE Advanced Sample Paper |
|
|
JEE Advanced PYQs |