
Complex stress analysis helps determine normal and shear stresses acting on inclined planes when multiple stresses act at a point. The topic covers plane stress, stress transformation, Mohr’s circle, principal stresses, maximum shear stress, complex strain and strain rosettes. These concepts are relevant to GATE Mechanical, Civil, Aerospace and XE examinations.
For GATE 2027 preparation, you need to understand the stress and strain transformation equations, apply the correct sign conventions, and practise numerical problems. GATE Wallah offers Mechanical and Civil and Aerospace Engineering batches, focusing on conceptual learning, comprehensive tests, and performance tracking to support subject preparation.
At a point in a three-dimensional body, three mutually perpendicular planes are associated with the x, y and z directions. Each plane carries:
One normal stress
Two shear stresses
Therefore, a three-dimensional stress state initially contains nine stress components.
Stress notation uses two subscripts:
The first subscript identifies the plane.
The second subscript identifies the direction of stress.
|
Plane |
First Subscript |
|
yz-plane |
x |
|
xz-plane |
y |
|
xy-plane |
z |
For example, on the yz-plane, σ_x is the normal stress, while τ_xy and τ_xz are shear stresses in the y and z directions, respectively.
The stress components at a point can be represented using a stress tensor:
|
x Direction |
y Direction |
z Direction |
|
|
x Plane |
σ_x |
τ_xy |
τ_xz |
|
y Plane |
τ_yx |
σ_y |
τ_yz |
|
z Plane |
τ_zx |
τ_zy |
σ_z |
The diagonal terms represent normal stresses, while the off-diagonal terms represent shear stresses. The stress tensor is symmetric:
τ_xy = τ_yx
τ_xz = τ_zx
τ_yz = τ_zy
These equal pairs are called complementary shear stresses.
Stress is a tensor quantity because its magnitude, direction and plane of action must be specified.
A three-dimensional stress state becomes a plane stress state when the stresses in the z direction are zero:
σ_z = 0
τ_xz = 0
τ_yz = 0
The remaining stress components are σ_x, σ_y and τ_xy.
The two-dimensional stress tensor is:
|
x Direction |
y Direction |
|
|
x Plane |
σ_x |
τ_xy |
|
y Plane |
τ_xy |
σ_y |
Axial, bending and torsional stresses are often evaluated on reference planes. However, an inclined surface may experience different normal and shear stresses. Such a surface is called an oblique plane.
Planning your GATE CSE and DA 2027 preparation in the final six months? Follow this last six-month roadmap for GATE CSE and DA 2027.
Let θ be the angle measured from the vertical plane. The normal stress and shear stress acting on the inclined plane are given by the stress transformation equations:
Normal stress:
σ_θ = (σ_x + σ_y)/2 + [(σ_x − σ_y)/2] cos 2θ + τ_xy sin 2θ
Shear stress:
τ_θ = −[(σ_x − σ_y)/2] sin 2θ + τ_xy cos 2θ
These equations are used to determine the stress components on an inclined plane. Candidates should memorise them and apply the prescribed sign conventions carefully.
The following sign conventions are used in the given formulation:
Tensile normal stress is positive.
Compressive normal stress is negative.
Shear stress acting upward on the right-side vertical plane is positive.
Shear stress acting downward on the right-side vertical plane is negative.
Anticlockwise angles measured from the vertical are positive.
Clockwise angles measured from the vertical are negative.
The angle must be measured from the vertical plane, even when a question provides the angle from the horizontal. Candidates should first convert the given angle into the reference convention used in the problem.
Memory Tip: For shear stress, inspect the right-side vertical plane: upward means positive and downward means negative. For the angle, anticlockwise from vertical is positive, while clockwise is negative.
Mohr’s circle is a graphical representation of stress transformation. It helps determine the normal and shear stresses acting on different planes without repeatedly applying the transformation equations.
The two axes represent:
Horizontal axis: Normal stress, σ
Vertical axis: Shear stress, τ
Every point on Mohr’s circle represents the stress state acting on a particular plane.
If a physical plane rotates through an angle θ, the corresponding movement on Mohr’s circle is 2θ.
Mohr’s Circle Angle = 2θ
Memory Tip: The angle doubles on Mohr’s circle. A physical plane rotation of θ corresponds to a circle movement of 2θ.
The centre of Mohr’s circle lies on the normal-stress axis and is calculated as:
C = (σ_x + σ_y)/2
The radius is:
R = √[ ((σ_x − σ_y)/2)² + τ_xy² ]
The radius also represents the maximum in-plane shear stress.
Mohr’s circle can be constructed using either of the following methods:
Calculate the centre and radius using the given stress components.
Locate the two plane-stress points and join them to form the diameter.
The two points are:
Vertical-plane point: (σ_x, τ_xy)
Horizontal-plane point: (σ_y, −τ_xy)
These points are diametrically opposite. Joining them gives the diameter of the circle.
For equal biaxial in-plane tension, where σ_x = σ_y and τ_xy = 0, both points coincide. Therefore, Mohr’s circle reduces to a single point.
This represents an equal biaxial in-plane normal stress state with zero shear stress. It should not be confused with three-dimensional hydrostatic stress, which requires equal normal stresses in all three directions.
A principal plane is a plane on which the shear stress is zero.
τ = 0
The normal stress acting on a principal plane is called the principal stress.
The two principal planes in a plane-stress state are perpendicular to each other. Their angular relationship is:
θ_p2 = θ_p1 + 90°
The first principal-plane angle is determined using:
θ_p1 = ½ tan⁻¹ [ 2τ_xy / (σ_x − σ_y) ]
The angle must be interpreted using the applicable sign convention and the correct quadrant.
The principal stresses are the normal stresses acting on the principal planes:
σ₁ = (σ_x + σ_y)/2 + R
σ₂ = (σ_x + σ_y)/2 − R
Here:
σ₁ = Maximum principal stress
σ₂ = Minimum principal stress
R = Radius of Mohr’s circle
Memory Tip: A principal plane has zero shear stress. The second principal plane is located 90° from the first.
The principal stresses are also the eigenvalues of the two-dimensional stress tensor. Their important relationships are:
Sum of principal stresses:
σ₁ + σ₂ = σ_x + σ_y
Product of principal stresses:
σ₁σ₂ = σ_xσ_y − τ_xy²
The first relationship represents the sum of the diagonal terms of the stress tensor. The second represents its determinant.
These relationships are useful for checking principal stress calculations.
For a plane-stress state, the maximum in-plane shear stress is equal to the radius of Mohr’s circle.
τ_max,in-plane = R
It can also be calculated using the two in-plane principal stresses:
τ_max,in-plane = |σ₁ − σ₂| / 2
In a three-dimensional stress state, the absolute maximum shear stress is determined by comparing the differences between all three principal stresses:
τ_max,absolute = max { |σ₁ − σ₂|/2, |σ₂ − σ₃|/2, |σ₃ − σ₁|/2 }
For a plane-stress state, the third principal stress is:
σ₃ = 0
Therefore, candidates should distinguish between the two quantities:
In-plane maximum shear stress: Use the σ₁ − σ₂ difference.
Absolute maximum shear stress: Compare all three principal-stress differences, including σ₃ = 0.
If a question specifically asks for in-plane maximum shear stress, use the radius of the two-dimensional Mohr’s circle. If it asks for absolute maximum shear stress, consider all three principal stresses.
Complex strain follows the same transformation approach as complex stress. The corresponding substitutions are:
σ becomes ε.
τ becomes γ/2.
The shear-strain term is γ/2, not γ, because γ represents engineering shear strain.
The same transformation principles apply to:
Strain on oblique planes
Principal strains
Mohr’s circle for strain
Biaxial and triaxial strain states
Memory Tip: To convert stress transformation equations into strain transformation equations, replace normal stress σ with normal strain ε, and shear stress τ with half the engineering shear strain, γ/2.
A strain gauge measures normal strain in the direction in which it is installed. A single gauge provides strain information in only one direction.
A complete two-dimensional strain state requires three components:
ε_x
ε_y
γ_xy
Therefore, at least three measurements are needed to determine the complete two-dimensional strain state. Three strain gauges attached together at different orientations form a strain rosette.
In a rectangular strain rosette, the gauges are separated by 45°. If gauges A and C align with the x and y directions, respectively:
ε_x = ε_A
ε_y = ε_C
Gauge B is placed at 45°. The engineering shear strain is calculated as:
γ_xy = 2ε_B − ε_A − ε_C
Memory Tip: For a rectangular strain rosette, remember:
γ_xy = 2B − A − C
Here, A, B and C represent the strain readings from the three gauges.
In a delta strain rosette, the gauges are separated by 60°. Different physical arrangements can produce the same type of strain readings.
Rectangular rosette problems are generally more common in examinations because delta-rosette calculations are longer.
Complex stresses and strains help determine how normal and shear stresses change with the orientation of a plane. For GATE 2027, you should understand stress transformation equations, Mohr’s circle, principal planes, principal stresses and both in-plane and absolute maximum shear stress.
GATE Wallah offers Mechanical Batches and Civil batches along with Aerospace Engineering batches. It focuses on concept-focused learning, comprehensive tests and performance tracking. These resources can support you in revising engineering concepts and practising numerical problems for GATE preparation.